Author Topic: Cant fit girvin vectors to 954 help please (Read 9865 times)

orange · « **Reply #15 on:** October 11, 2008, 01:50:22 pm »

Quote

The gripshifts for the gears are badly perished and i guess i wont be able to replace the rubber grips so i expect i will have to change these , ( reccomendations welcome on that )

you'll find some on ebay if you look around, or find some old ones where the grips aren't too damaged and swap them over

in terms of elastomers/springs - stick up a new thread specifically on that subject on this forum, it may catch Callum's (Rapiddescentscotland) eye - he' s posted very recently so is around here.

shovelon · « **Reply #16 on:** October 11, 2008, 02:29:13 pm »

Quote from: sid on October 11, 2008, 01:03:50 pm

UPDATE :

P.P.S If someone lets me know how to meaure the frame size , i will let you know that as well , I thought it was from the centre of the crank to the top of the top tube but not entiterly sure .

I am pretty sure that from center of seat tube along top tube to center of head tube is 23 inches for a large frame(Thats what mine are anyway).

Terry

purple gerbil · « **Reply #17 on:** October 12, 2008, 04:41:11 am »

HI THERE SID!!!

first off here are the 954 frame sizes straight from the catalogue!!
centre of b/b to centre of t/tube...measuring up along the s/tube
14" 355mm
16" 405mm
18" 458mm
20" 509mm

also could you try retro fitting a ods system??? measurement's and photo's anyone!!

and some pic's...sorry but these are photo's as my 2yr old stood on my scanner (DOH!)

sid · « **Reply #18 on:** October 12, 2008, 10:43:31 am »

Thanks for that purple gerbil , I dont suppose theres any chance scanning the front of the bike in aswell .

Measured up frame and its 18" , mine is not as shiney as the one in the picture though

jeffhop · « **Reply #19 on:** October 12, 2008, 11:43:33 am »

sid if you use the scroll bar on the bottom of purple gerbils post you will see both ends of the bike

sid · « **Reply #20 on:** October 12, 2008, 12:19:51 pm »

Opps !

kiwi · « **Reply #21 on:** October 13, 2008, 01:10:29 am »

i didnt think a 954 had a "shock",therefore a spring will be very bouncy...

sid · « **Reply #22 on:** October 13, 2008, 01:49:07 am »

Hi Kiwi ,

This is what i dont quite understand and am trying to sort out , is my unit just full of grease and should be hard to push in or should you be able to push it in with out it returning on its own , and how hard should it be to push in , how do i refill it ?

Many thanks

( i was only interested in a coil on the rear as i saw it on the picture on this thread on page 1 so I thought it was possible to do as the unit inside the coil is the same as mine , maybe who everdone it is hanging off a tree as we write )

shovelon · « **Reply #23 on:** October 13, 2008, 09:19:50 am »

Quote from: sid on October 13, 2008, 01:49:07 am

( i was only interested in a coil on the rear as i saw it on the picture on this thread on page 1 so I thought it was possible to do as the unit inside the coil is the same as mine , maybe who everdone it is hanging off a tree as we write )

Yes, either he is hanging off a tree, or he put the coil on for show

5 inches of travel eh? SWEEET!

purple gerbil · « **Reply #24 on:** October 13, 2008, 03:00:22 pm »

that be 3.1" of travel and a generation 5.... pay attention terry

whats the dia of a ods unit??

sid whats the dia of 954 shock unit...?

if 954 is bigger then can it be shimmed like you would do on a seatpost???

shovelon · « **Reply #25 on:** October 13, 2008, 04:29:11 pm »

Quote from: purple gerbil on October 13, 2008, 03:00:22 pm

that be 3.1" of travel and a generation 5.... pay attention terry

Ha, got me on that one.

The wife uses the same line on me constantly.

purple gerbil · « **Reply #26 on:** October 14, 2008, 11:49:32 am »

(lol) which bit!!

3.1" or pay attention!!

shovelon · « **Reply #27 on:** October 14, 2008, 11:55:34 am »

Quote from: purple gerbil on October 14, 2008, 11:49:32 am

(lol) which bit!!

3.1" or pay attention!!

Both

sid · « **Reply #28 on:** October 20, 2008, 02:37:44 pm »

UPDATE:

Have now won all the bits on flee bay that I need to finish my 954 so will be hopefully finishing in the next week or so depending on time / delivery .

Cheers all

orange · « **Reply #29 on:** October 21, 2008, 09:19:59 am »

pics when done then - this should be good - a rare one.

News:

Menu

Picture Bit

Author Topic: Cant fit girvin vectors to 954 help please (Read 9865 times)