Author Topic: POST BUY SELL WANT,proflex and K2 finds here! (Read 446226 times)

antmav · « **Reply #1140 on:** August 11, 2011, 06:52:52 pm »

Chris,
Thanks Man!

Will I be able to find a Noleen J6 or a Riesse for the 656? Are they still manufacturing new one's or would I have to scan Craigslit or Fleabay? Would the shock have to be retro fit or will it just work with the current rear end? I know it's a ton of questions, but I've always just replaced the MDU's when needed, never swapped out the rubber for air.

Thanks in advance>

~Ant

w2zero · « **Reply #1141 on:** August 11, 2011, 07:05:16 pm »

You can find them here. http://shop.noleenj6.com/category.sc;jsessionid=540DDEDE98B2B892762EB632DAC0BC1B.qscstrfrnt05?categoryId=7 Not cheap but that's the price of admission.

kiwi · « **Reply #1142 on:** August 12, 2011, 04:16:49 am »

Quote from: Spokes on August 11, 2011, 12:30:49 pm

Your frame will be a small as they didnt make a way small. It has a double stack just like the other sizes. Noleenj6 make straight swap quality shocks for the '56 models as well as Risse. Both will out perform MDU by far.

Chris

nope...656 quite different to 756 etc

antmav · « **Reply #1143 on:** August 12, 2011, 05:49:23 am »

Thanks for the link. I just checked the Noleen site and there wasn't a rear shock listed that would fit a 656. Any other options you can think of?

Thanks

DugB · « **Reply #1144 on:** August 12, 2011, 06:24:39 am »

Hmmm...I don't even know if Risse would have something for that rear. What about going with new elastomers from Suspension Fork Parts? Would probably run $100 total for the front and rear. Or, you could always try to find a replacement material or spring yourself. There are cheap springs on eBay all the time, and all you really need are your measurements (e.g. ID, OD, free length) and the spring rate (maybe 400 lbs for that rear?).

Just my $0.02...

- Doug

antmav · « **Reply #1145 on:** August 12, 2011, 07:22:04 am »

Yes, thanks, that's what my orig post asked......if I should just get a few elastomers from Suspensionforkparts.com or look for an air can.

kiwi · « **Reply #1146 on:** August 12, 2011, 05:55:19 pm »

Quote from: antmav on August 12, 2011, 07:22:04 am

Yes, thanks, that's what my orig post asked......if I should just get a few elastomers from Suspensionforkparts.com or look for an air can.

i think you only have room for a new set of elastomers.There just isnt room there for any kind of shock.

antmav · « **Reply #1147 on:** August 14, 2011, 02:58:48 pm »

Ok, thanks so much for the info. I'll order up some new elastomers tonight.

shovelon · « **Reply #1148 on:** August 14, 2011, 06:00:41 pm »

Or this?

pczeilon · « **Reply #1149 on:** August 14, 2011, 06:54:35 pm »

Just picked up a 954 to keep my Reptile company. I'm in need of the plastic spacers that go between the 2 elastomers both front & rear. I believe these are pretty much the same for all models & years of Proflex. Let me know if this is incorrect. If any of you who have upgraded to "real' shocks still have your spacers laying around I would really appreciate you sending them my way!

Spokes · « **Reply #1150 on:** August 15, 2011, 02:18:25 pm »

nope...656 quite different to 756 etc

Ah well I had one of them right. Risse do make a shock for it. And it does use two elastomers. Id probably stick with elastomers on that model.

Chris

kiwi · « **Reply #1151 on:** August 16, 2011, 01:20:58 am »

i dint realise risse made a shock for the 656(954?) frame.

Lamima · « **Reply #1152 on:** August 16, 2011, 06:10:33 am »

I need two tefllon rings for the main pivot auf an 552....
Mine are looking not good anymore

Brycer1968 · « **Reply #1153 on:** August 16, 2011, 01:06:29 pm »

Hi there. Im new to owning a Girvin Proflex elite crosslionk fork and I'm looking for some spare aluminuim fork legs for a snow bike project where I'll be pairing this fork with a Surly Large Marge rim and 3.8" tire. The fork modifications will only require the portion of the fork legs below the pivots. The upper pivot part fo the fork legs can be damaged/worn or not even there.

I am assuming that all the aluminum Girvin fork leg extrusions are the same diameter, profile and thickness over the years and models. I'm also assuming that the legs are straight gauge and not butted like bike frame tubing. . . . Maybe someone here can weigh in on these questions as well

Please let me know if you have spare Girvin legs in your parts inventory that might work for this. I can paypal you the shipping cost plus what ever you think they are worth.

By way of introduction, I'm new on here, but I buy and sell Magura rim brakes from the 1990s and 2000s, so I have a huge inventory of HS22 and HS33 brakes and parts in all colors spanning the Miami Vice color pallette as well as booring black and silver. I spend a lot of time on this forum: http://www.unicyclist.com/forums/showthread.php?t=89493

Cheers,
Bryce Jacobson, Portland, Oregon
uniflasher@hotmail.com

spikebender · « **Reply #1154 on:** August 21, 2011, 12:19:35 pm »

Hey, can you give a little info on the shock replacement on the 656 photo thats posted thanks, Tracy

News:

Menu

Picture Bit

Author Topic: POST BUY SELL WANT,proflex and K2 finds here! (Read 446226 times)